
How to Install Carpet Treads on Stairs with a Deep Nosing Overhang
About This Project
This project outlines the steps for installing carpet treads on stairs that have a deep nosing overhang. It covers measuring, cutting, fitting, and securing the treads to ensure a safe and aesthetically pleasing result.
Tools & Materials
Measuring Tape

Carpet Knife

AdirOffice 36 in. x 48 in. Self Healing Reversible Cutting Mat, Green/Black CM3648

TrafficMaster Hanville - Linen - Beige 27 oz. SD Polyester Loop Installed Carpet 0805D-24-12

Klein Tools 8 in. Heavy-Duty Carpet Shears 23018SEN

PURE ERA Bullnose Indoor Tape Free Non-Slip Gray 9.5 in. x 30 in. x 1.2 in. Polypropylene Carpet Stair Tread Cover (Set of 14) PE-ST01-GR14
Measuring Tape
For accurate measurements of plywood and components, ensuring proper assembly.

Carpet Knife
Precision blade crafted for carpet cuts.

AdirOffice 36 in. x 48 in. Self Healing Reversible Cutting Mat, Green/Black CM3648
The AdirOffice cutting mats are made from 3-ply high-tech polymer material. Constructed with a self-healing surface the mats are extremely durable and hold up under repeated use with art and mat knives

TrafficMaster Hanville - Linen - Beige 27 oz. SD Polyester Loop Installed Carpet 0805D-24-12
Hanville is a 27 oz. Solution Dyed Polyester. It is an excellent carpet for high traffic areas that require tough wear with a splash of style and design. Southwest is a light-colored looped style with

Klein Tools 8 in. Heavy-Duty Carpet Shears 23018SEN
These Klein Tools, Inc. 8 in. Heavy-Duty Carpet Shears feature sharp steel blades for precisely cutting stained or damaged fibers and the wide blade design helps ensure level cutting. The shears are shaped

PURE ERA Bullnose Indoor Tape Free Non-Slip Gray 9.5 in. x 30 in. x 1.2 in. Polypropylene Carpet Stair Tread Cover (Set of 14) PE-ST01-GR14
Everyone loves a beautiful hardwood stairway, but even the most attractive stairs can be slippery for anyone in the family, including pets. PURE ERA Carpet Stair Treads can add safety to your steps, not
Steps
Measure Existing Tread Depth and Nosing
15 minutesCarefully measure the depth of each stair tread from the front edge to the riser. Also, measure the overhang of the nosing on each tread. Record these measurements accurately, as they will be crucial for cutting the carpet treads to the correct size.
Watch: Measure Treads and Mark LaminateCut Carpet Treads to Size
30 minutesUsing your recorded measurements, cut the carpet material for each tread. The cut piece should match the tread depth and extend to cover the nosing. If your carpet has a backing, ensure you cut through both the carpet pile and the backing cleanly. For a clean edge, you might consider cutting slightly larger and then trimming to fit precisely in the next step.
Watch: Measure and Cut CarpetDry Fit and Trim Carpet Treads
20 minutesPlace each cut carpet tread onto its intended stair to check the fit. Pay close attention to how it sits around the nosing and against the riser. Make any necessary small adjustments or trims to ensure the carpet lies flat and covers the tread area completely without bunching or leaving gaps. The goal is a precise fit that follows the contours of the stair.
Watch: Test Fit and Adjust TreadsApply Adhesive to Treads
25 minutesDepending on the adhesive type, apply it either to the back of the dry-fit carpet tread or directly onto the stair tread surface. Ensure even coverage across the entire area that will contact the stair, paying special attention to the nosing. Use an adhesive recommended for carpets and wood or your specific stair material, and follow the manufacturer's instructions regarding application method and drying/tack time.
Watch: Apply Adhesive to TreadsInstall Carpet Treads
30 minutesWith the adhesive applied, carefully align the carpet tread with the stair tread. Press down firmly, starting from the back and working towards the nosing, to ensure full contact and adhesion. Apply even pressure across the entire surface, especially along the edges and over the nosing, to eliminate any air bubbles and create a strong bond. Use a roller or your hands to press firmly.
Watch: Install Carpet TreadsSecure Nosing Overhang
15 minutesFor carpets with a distinct nosing overhang, ensure the carpet is pressed firmly down over the front edge of the stair. The adhesive should hold it in place. If the carpet tends to lift, you may need to apply a bit more adhesive specifically to the underside of the nosing overhang before pressing the carpet down. Some systems might also use a small tack strip or staple in inconspicuous areas if the carpet type and adhesive allow, but this is often not necessary with good adhesive.
Watch: Pre-form and Secure Carpet Underneath TreadAllow Adhesive to Cure
1440 minutesAfter all carpet treads have been installed and pressed down, allow the adhesive to cure completely. Refer to the adhesive manufacturer's instructions for the recommended curing time. This typically ranges from 24 to 72 hours. During this period, avoid heavy foot traffic on the stairs to ensure the treads are securely bonded and do not shift.
Watch: Project Completion








