Skip to main content

Install New Faucet Body — Install the New Tub Faucet

Beginner

Part of project

Bathroom Tub Faucet Replacement: A Step-by-Step DIY Guide · Step 4 of 4

Helpful?

In this video

Take the new faucet assembly and carefully feed the attached hoses and wires down through the mounting hole in the countertop. Ensure the faucet base is seated correctly on the countertop surface. From underneath the sink, slide the plastic mounting bracket up over the hoses and onto the faucet's threaded shank. Follow this with the large brass mounting nut, threading it onto the shank by hand. Use the included plastic tightening tool to fully tighten the nut, securing the faucet assembly. Check the faucet's alignment from above to ensure it is straight. Finally, use a Phillips head screwdriver to tighten the two screws on the mounting bracket, which will clamp it against the underside of the counter and prevent the faucet from rotating.

Goal: Secure the new faucet to the countertop

  • Have someone hold the faucet in the correct position from above while you tighten it from below to ensure proper alignment.

Used in this video

  • Included plastic tightening tool (Tool Type: Faucet Wrench, Power Source: Manual) · optional — Tightening the mounting nut in the tight space under the sink.
  • Screwdriver (Tool Type: Screwdriver, Power Source: Manual, Handle Type: Phillips) · optional — Tightening the two securing screws on the mounting bracket.
11.5K views11025 minutes
Everyday Home Repairs

1.1M subscribers

View Channel

FAQs

What should I do if I can't locate the shut-off valves for my bathtub, or if they don't work?

If individual tub shut-off valves are missing or malfunctioning, you'll need to turn off the main water supply to your entire house. The main valve is usually located where the water line enters your home, often in a basement, utility closet, or near the water heater. After turning off the main supply, open a lower-level faucet to drain water from the pipes before proceeding with the tub faucet replacement.

Beyond the adjustable wrench and screwdriver, are there any other tools that might make this tub faucet replacement project easier?

While the basic tools will suffice, a deep socket set (specifically for valve stems) or a basin wrench can be incredibly helpful for accessing and loosening nuts in tight spaces. You might also want a utility knife or scraper for removing old caulk or plumber's putty, and a flashlight for better visibility under the tub.

As a beginner, how much time should I allocate for replacing my tub faucet, and what's the typical cost for a new one?

For a beginner, this project typically takes between 1 to 3 hours, depending on how easily the old components come apart. The cost of a new tub faucet can vary widely, from around $50 for a basic model to several hundred dollars for high-end designer fixtures, so choose one that fits your budget and style.

What are the most common mistakes people make when replacing a tub faucet, and how can I avoid leaks after installation?

Common mistakes include not completely turning off the water, overtightening connections, or failing to use enough plumber's putty or thread sealant where required. To prevent leaks, ensure all connections are snug but not overtightened, apply plumber's putty consistently under the new faucet base, and always test for leaks thoroughly before closing up any access panels.

Transcript
Hide

The first step of the installation is just take the entire faucet assembly, shove all the hoses down the hole and just pull everything through. Pretty straightforward. Now, because I have a stone or granite countertop, I don't have to worry about the faucet touching anything metal. Obviously, if you have a metal sink and it's touching the metal on the sink, you could have issues with the touch faucets. So you have to make sure that the threaded metal portion of that thing is not touching anything on the sink. It does come with a handy tool to screw the nut on that's going to secure the faucet to the sink. And to tighten the entire faucet down, I'm going to put on the mounting bracket, which is the square plastic piece. It does have to get oriented in a specific direction. You can see the braided hose was fed through the bracket and then all the PEX tubing actually has a little slot on the one side of the bracket. So that does not get threaded through that hole with everything. And then I'm just going to take that brass nut and I'm going to screw that onto the bottom of the faucet and tighten it up until the faucet is secured against the counter. Now you do have to make sure that the faucet is oriented straight. There's like a little, it says dealt on the faucet. Obviously that's going to point towards the front and the there's a little light on it as well. And that has to point forward. Obviously it's pretty easy to center this thing, particularly because I have covered doors on both sides of my sink for some, some reason. I'm not really sure why, but it definitely makes installing a faucet a lot easier when you can access it from both sides. And then there's two screws on the bottom of the bracket and you just tighten those up very straightforward and it goes on nice and secure.

Auto-generated transcript. May contain errors.